Wiki Page: Unable To Uninstall AutoPLANT [TN]
Applies To Product(s): AutoPLANT V8i Version(s): V8i Environment: N/A Area: N/A Subarea: N/A Original Author: Elias Morkos, Bentley Technical Support Group Overview On rare occasions, the uninstall...
View ArticleWiki Page: Structural Modeling Components Initialization Error in OpenPlant...
Applies To Product(s): OpenPlant Modeler Version(s): 08.11.11.87(SS6) & Above Environment: Windows 7 (64 bit) & Others Area: Component Subarea: Structural - Placement Original Author: Rahul...
View ArticleWiki Page: How to Identify Inconsistency of Component Data with Consistency...
Applies To Product(s): OpenPlant Modeler Version(s): 08.11.09.XXX (SS5) & 08.11.11.xx (SS6) Environment: Windows 7 (64 bit) Area: Component Subarea: Data Original Author: Harpreet Singh, Bentley...
View ArticleWiki Page: How to Exclude a Property From Consistency Checker
Applies To Product(s): OpenPlant Modeler Version(s): 08.11.09.XXX (SS5) & 08.11.11.XX (SS6) Environment: Windows 7/8 (64 bit) Area: Component Subarea: Data Original Author: Harpreet Singh, Bentley...
View ArticleWiki Page: Properties - OpenPlant Modeler
Properties - OpenPlant Modeler To Discuss Properties related Issue. See Index: How to Add Component's Facing Property in Element Information dialog How to Add Inch Sign with Nominal Diameter in...
View ArticleForum Post: RE: OPPPID Drawing Revision
Thanks very much for your help. I wish you had answered this before as I was told that it is a defect issue by the other support person.
View ArticleForum Post: OPIM - Label pointed to same point
Hi, Using OPIM .87 with AutoPLANT .235. When extracting isometric I'm getting very strange result. Most of the label's origins are comming from a point outside of the bounderies. See picture in the...
View ArticleForum Post: OPIM - Isometric with Tee Shoe Support takes forever
Hi, I'm using OPIM .87 with AutoPLANT .235 When a tee support is included in an ismetric OPIM takes foever to run in fact I had to kill it because I didn't see the end. If the selection doesn't include...
View ArticleForum Post: RE: OPIM - Isometric with Tee Shoe Support takes forever
Just found that having a comment attached to a support cause the problem. Need to move the comment on the pipe near the support.
View ArticleForum Post: RE: OPIM - Isometric with Tee Shoe Support takes forever
Thanks Stephane to confirm! I believe you are getting correct results now. -Regards | Rahul Kumar
View ArticleForum Post: RE: OPIM - Label pointed to same point
Hello Stephane, I believe it is style specific. If you check different style, it should work correctly. Further you can carefully compare the changes you have done. you could try various things, like...
View ArticleForum Post: RE: OPIM - Isometric with Tee Shoe Support takes forever
I'am having a good result because of the workaround, There still a problem where a comment can't be placed on a support. SH
View ArticleForum Post: RE: OPIM - Label pointed to same point
Rahul, I tried with different style and still getting the same nice Picasso result. I did many isometric with the same style without having this problem and suddenly it happens. Not sure how to resolve...
View ArticleForum Post: OPIM - Component is not connected to
Hi, Using OPIM .87 with AutoPLANT .235 OPIM gives error messages about components not connected even if it is connected (conncectivity cherker didn't found disconnected component) This occurs many...
View ArticleForum Post: RE: OPIM - Component is not connected to
Hello Stephane, Can you please upload your project through project packager for our testing. We will check all your concern and reply back to you. Files to upload -...
View ArticleForum Post: RE: OPIM - Label pointed to same point
Hello Stephan, Could you please try following settings: 1. Open "Seed.dgn" file. 2. Go to menu Workspace > Configuration 3. Click on New on the right hand side 4. New Configuration Variable box...
View ArticleFile: Readme file for OpenPlant Isometrics Manager V8i (SELECTseries 6)...
Readme file for OpenPlant Isometrics Manager V8i (SELECTseries 6) Refresh 1 is available for download. Please review this file for information on system requirements, licensing, software pre requisites...
View ArticleForum Post: Unable to use half coupling in open plant SS5
I am unable to use half coupling in open plant. I have added specs of the half coupling but when I select the coupling it shows only full coupling.
View ArticleForum Post: RE: Unable to use half coupling in open plant SS5
Hi Jayant, How are you trying to place Half Coupling? Are you getting any error or message? What is the version of OpenPlant Modeler you are using? Please see below wiki article which might help you in...
View Article