Forum Post: How to show insulation along a pipe not the whole pipe?
How can you show Insulation along a pipe but no the whole pipe? Personal protection insulation is usually around 2.4m above the ground and below, where a pipe runs from within this level to higher, the...
View ArticleForum Post: RE: How to show insulation along a pipe not the whole pipe?
Hi Ray, Currently there is no possibility to apply insulation on few components. Please see below discussion on the same topic. However, as a workaround, you can apply insulation on individual...
View ArticleForum Post: OPM SS6 - bolt missing between LUG butterfly valve and RF flanges
Hi, I created a butterfly valve with LUG conditions at both ends. When I try to connect the valve to an RF flange, the bolt is missing, only the gasket is placed. Any suggestion as to what is missing?...
View ArticleForum Post: OPM SS6 - Standard mEX-OPM spec's butterfly valve is missing
When I ran a test using the standard OPM_Metric project and mEX-OPM spec, I couldn't place butterfly valve of any size. The program through the usual "No component found with initial selection from...
View ArticleForum Post: RE: OPM SS6 - How to create joint between PE/BW ends with PFS ends?
Hi Harpreet, Sorry for the late reply, but I didn't get any error message when placing the rain_cap. The cap just doesn't connect up with the pipe component. When iso generated, the cap is placed on a...
View ArticleForum Post: How to get pipe/elbow connect point's coordinate in MVBA
Hello All, I'd like to get the coordinate of connect points of pipe/elbow. I did scan the property of OPM imodel (PropertyHandler), I find TRANSFORMATION_MATRIX.M03/07/11 are x/y/z of one connect...
View ArticleForum Post: RE: OPM SS6 - Standard mEX-OPM spec's butterfly valve is missing
Hi Tuan, I tried 150mm size on my end and it worked, please see below: Attaching same example spec for your reference. Hope this helps! Regards, Harpreet
View ArticleForum Post: RE: How to get pipe/elbow connect point's coordinate in MVBA
Hi Changsong, Could you please explain why do you need the center point of elbow through MVBA? Regards, Harpreet
View ArticleForum Post: RE: How to get pipe/elbow connect point's coordinate in MVBA
Hello, I'm trying to create a MVBA to label the PGA drawing, so I need the center point of the elbow. Thanks.
View ArticleForum Post: RE: How to get pipe/elbow connect point's coordinate in MVBA
I am not sure about the MVBA but in the upcoming release of OpenPlant Modeler, a center point of an elbow has been added which can also be snapped for dimensioning and measuring purposes. Regards,...
View ArticleForum Post: RE: How to get pipe/elbow connect point's coordinate in MVBA
How about pipe? I can get only one connect point(TRANSFORMATION_MATRIX.M03/07/11 ) , what's the another connect point?
View ArticleForum Post: Dummy Lag Support - Origin Location
When a Dummy Leg Support is placed on a pipe, the origin of the support is some random number away from the actual origin of where it should be. How is OPM calculating the origin of the support and...
View ArticleForum Post: RE: Dummy Lag Support - Origin Location
Hello Ray Lucas, Have you tried to use OpenPlant Support Engineering for support placement? I believe you won't get this problem with it. Regarding your situation in OpenPlant Modeler, I would like to...
View ArticleWiki Page: To Modify Default Outside Diameter Value for End Types in...
Applies To Product(s): OpenPlant Modeler Version(s): 08.11.09.XXX (SS5) | 08.11.11.XX (SS6) Environment: Windows 7/8.1/10 (64 bit) Area: OpenPlant Specification Generator Subarea: - Original Author:...
View ArticleForum Post: RE: Slip on joint in weld report in OPM
Hello Jayant, We are evaluating the case. We will get back to you shortly on this. -Regards | Rahul Kumar
View ArticleForum Post: RE: OPM SS6 - How to create joint between PE/BW ends with PFS ends?
Hi Tuan, You will need to define the end preparation in Weld Value Map class as shown below. PFS end condition is already defined for PUSH_ON_END, so you might need to rename either of them. Hope this...
View ArticleForum Post: RE: OPM SS6 - bolt missing between LUG butterfly valve and RF...
Hi Tuan, Please see below wiki article for your reference. Regards, Harpreet
View ArticleForum Post: RE: Dummy Lag Support - Origin Location
Hi Kestutis, Thanks for the response, will OP Support Engineering give me the correct length of the dummy leg on the Isometric when it is run? I'm thinking no would be the answer to that. If not then I...
View ArticleForum Post: RE: How to show insulation along a pipe not the whole pipe?
With regard to my work around above, can you please point me to a Wiki that shows how to add a new type of weld.
View Article