Forum Post: AutoISO Relationship Manager error code reported -2147467259
When I have Isometrics open and I open a 3D drawing and start AutoISO, it will run through like it is working correctly, but breaks out the drawing into individual parts (one part for each new...
View ArticleForum Post: RE: AutoISO Relationship Manager error code reported -2147467259
Hello Paul, Thanks for the question. Could you also raise service request for the same. Regards,
View ArticleForum Post: RE: Isometric Dimension to Midpoint for all items
Thanks Frank, Based on SR # 7000667150 , we have logged a Defect # 757282 to it. Submitting it for your information please. HTH -Regards | Rahul Kumar
View ArticleForum Post: RE: Isometric Continuations with nested references
Hello Shannon, While evaluating this link, I realized that we had a a discussion on this. Based on SR # 7000623239 , we have logged a Defect # 689890 to this item & it is under review with Product...
View ArticleWiki Page: OPPID - Ss6 Known Issues
Known Issues in OpenPlant PID V8 i (SELECTseries 6) V08.11.11 Known Issues of OpenPlant PID V8 i (SELECTseries 6) Drafting: Whenever InRun Spec Validation dialog is opened, you must Apply (green check...
View ArticleWiki Page: OPPID - Ss6 Requirements
OpenPlant PID V8 i (SELECTseries 6) Requirements Processor Memory Hard disk Input device Output device Video Graphics card Operating system Optional Integrations Processor Intel ® or AMD ® processor...
View ArticleWiki Page: OPPID - Ss6 What is New
What is New in OpenPlant PID V8 i (SELECTseries 6) V08.11.11 What’s New? The OpenPlant PID V8 i (SELECTseries 6) release is the latest release of our newest Intelligent P&ID Solution. OpenPlant PID...
View ArticleForum Post: 通过图标生成槽钢时 出现'NoneType' object is not iterable错误
import clr from Bentley.ESM.Geometry import * import BESM from BESM import * import BasicShapes import SuppPlacement import Bentley.ESM.Placement from Bentley.ESM.Placement import * import...
View ArticleForum Post: RE: 通过图标生成槽钢时 出现'NoneType' object is not iterable错误
Hello, Can you provide version information you are using here? Also please attach script file for our investigation. As above information about scripts are not correctly imported. -Regards | Rahul Kumar
View ArticleForum Post: Instrument location codes in OPPID
Most sheet borders have letters up the sides and numbers across the top and bottom to help in locating items on the drawing. In the instrument table there is a field called 'Location Code'. Is this the...
View ArticleForum Post: RE: Instrument location codes in OPPID
Hello, The Location Code field in the database is used to store the value for the instrument location based on the instrument type - Field, Control Room Panel, Back of Control Room panel etc. In terms...
View ArticleWiki Page: How to Run Project Wizard in AXSYS.Process CONNECT Edition
This content is under review.
View ArticleWiki Page: How to Generate PFD in AXSYS.Process CONNECT Edition
Go to Start > Run AXSYS.Process Project Wizard. Select “Create a New Project” from the list. Press” Next” Press “Next” Press ‘Next’ Press ‘Next’ Press ‘Next’ Press ‘Close’ as Project is Created....
View ArticleWiki Page: How to Generate PID in AXSYS.Process CONNECT Edition
Go to Start > Run AXSYS.Process Project Wizard. Select “Create a New Project” from the list. Press” Next” Press “Next” Press ‘Next’ Press ‘Next’ Press ‘Next’ Press ‘Close’ as Project is Created....
View ArticleWiki Page: How to Place a valve in PFD in AXSYS.Process CONNECT Edition
Go to Start > Run AXSYS.Process Project Wizard. Select “Create a New Project” from the list. Press” Next” Press “Next” Press ‘Next’ Press ‘Next’ Press ‘Next’ Press ‘Close’ as Project is Created....
View ArticleWiki Page: How to Reorder Iso Sheet Numbering Using Pipeline Start Note in...
Applies To Product(s): OpenPlant Modeler Version(s): 08.11.11.87 (SS6) & Above Environment: Windows 7/8.1/10 (64 bit) Area: component Subarea: Place Note - Pipeline Start Point Original Author:...
View ArticleWiki Page: How to use Branch3D symbol for custom TEE in OpenPlant Isometrics...
Applies to Product(s): OpenPlant Isometrics Manager Version(s): 08.11.11.224 Environment: Windows 7/8.1/10 (64 bit) & others Area: Settings/Attributes Subarea: Modifying Symbols Original Author:...
View ArticleForum Post: RE: Instrument location codes in OPPID
Thanks Tony, There is another field named Instr_Loc, can this one be used in the interim?
View ArticleForum Post: moving components coordinately in AutoPLANT 3D 2012 version.
This is probably a very simple task, but I have to ask how do you move something coordinately? When I use the move command and pick what I want to move it doesn't want me to move things by coordinates....
View Article