Forum Post: RE: OpenPlant Modeler & OpenPlant PID
Hi Ihor, You can check the instances which are not matching through consistency report. Use "mechaddin ccrepot" key-in. Please refer below wiki article: Hope this helps! Regards, Harpreet
View ArticleWiki Page: "[Error 319] Cannot Start Application for the Specified Document"...
Applies To Product(s): OpenPlant Modeler Version(s): 08.11.09.XXX (SS5) | 08.11.11.XXX (SS6) Environment: Windows 7/8.1/10 (64 bit) Area: ProjectWise Subarea: Original Author: Harpreet Singh, Bentley...
View ArticleWiki Page: Importing Models into ProjectWise Loses Reference File Path
Applies To Product(s): OpenPlant Modeler Version(s): 08.11.09.XXX (SS5) | 08.11.11.XXX (SS6) Environment: Windows 7/8.1/10 (64 bit) Area: ProjectWise Subarea: Original Author: Harpreet Singh, Bentley...
View ArticleWiki Page: ProjectWise - OpenPlant Modeler
ProjectWise - OpenPlant Modeler ProjectWise - OpenPlant Modeler To Discuss ProjectWise related Issue. See Index: "[Error 319] Cannot Start Application for the Specified Document" on Opening the File...
View ArticleForum Post: OpenPlant Project Administrator / OpenPlant Modeler
Hello to Bentley! I have a problem with autoflange. I set what I need in AutoFlange field in Specification Generator (see below), but the result is following: Please advice, how to solve it and where...
View ArticleForum Post: Tapered spacer in OPM
Hello All, I'd like to know if OPM support tapered spacer. If supported, how to create it in pipe spec? And does it distinguish one-side tapered spacer and two-side tapered spacer? Thanks a lot!
View ArticleForum Post: RE: OpenPlant Project Administrator / OpenPlant Modeler
Hello Mr. Ihor Didyk, Please review this article in which are detail information about how to have automatic flanges placement for required components....
View ArticleWiki Page: Set DWG working units on OPPID Conversion in PCF file
When working with Managed Workspaces and importing the AutoPLANT PID Conversion schemas drawing creation is an issue due to a working units mismatch. This mismatch is between the DGN/DWG default seed...
View ArticleForum Post: RE: Tapered spacer in OPM
Hi Changsong, You can create custom class in schema and then create cell for placement in modeler. You can follow the similar wiki articles for this requirement. On spec data front, I believe this has...
View ArticleForum Post: RE: Tapered spacer in OPM
OPM does not support tapered spacer right now? I saw the articles above, they look like just add a cutomised-fixed components, I'd like to add a serials of (all DN) tapered spacers.
View ArticleForum Post: How to add a new end preparation in OPM
If the end preparation is "FL" (Flanged), the end preparation abbreviation "FL" will be appended to the ISO symbol name. For example, the ISO symbol name of elbow is 90**, for flaned elbow, the ISO...
View ArticleForum Post: RE: Snap to quardrants of a pipe?
It is not correct. you can see the attached youtube clip, which veritify that it is possible to use Quadrant Snap on a 3D object in autocad but not on a 3D autoplant object. But thanks for your answers...
View ArticleForum Post: RE: How to add a new end preparation in OPM
Hello Changsong, Review this wiki with possible solution of how to not show gasket for Flanges in OpenPlant Modeler and in generated Isometrics:...
View ArticleForum Post: RE: How to add a new end preparation in OPM
Only one spec doesn't need gasket, all others need gasket still. I have found the the way to add the end preparation mapping, add a new record in...
View ArticleWiki Page: Error 374 VB.UserControl Received While Opening Document Manager...
Applies To Product(s): Document Manager/Vision Version(s): All Environment: N/A Area: N/A Subarea: N/A Original Author: Bentley Technical Support Group Overview If a user receives the error message...
View ArticleForum Post: Bolt Length cannot be calculated
Hello All, I created a new flanged end prep type, joint type, end prep type ISO map, it works fine in OPM and ISO. The content I created, I copied from standard flange, all contents are almost same as...
View ArticleForum Post: RE: Bolt Length cannot be calculated
Hi Changsong, We have several wiki articles on Bolt Length calculation which will give you an idea on how is bolt length calculated. One of them is given below: Can you provide some more details about...
View ArticleForum Post: RE: Bolt Length cannot be calculated
Hello Changsong In addition to above query, can you please let us know, what version of OpenPlant Modeler you are using? -Regards | Rahul Kumar
View ArticleForum Post: RE: Bolt Length cannot be calculated
I am using OPM 08.11.09.568. Sorry that article cannot help me. It explained how calculate the bolt length, my problem is it cannot calculate. For example, Stud Bolt_Length = (Gasket_Thickness) +...
View Article